datasheet | january 2012 fiber optics | rev 2012.01 information contained herein is deemed reliable and accurate as of the issue date. emcore reserves the right to change the desi gn or specification at any time without notice. applications high performance supertrunking links high power distri bution networks fiber deep architectures fttx networks features full function high power fiber optic amplifier low noise figure (typ < 6 db) total input power range: -10 dbm to +12 dbm total ouput power: +27 dbm to +37 dbm (optical ouput power splitter is optional for these units) standard rs-232 communications standard snmp communication (coming soon) low electrical power consumption input/output isolation >40/40 db polarization dependant gain < 0.1 db polarization mode dispersion < 0.5 ps pona 3000 series erbium doped fiber amplifier the emcore pona 3000 series fiber optical amplifier module is an ideal building block for oem system integrator s. the family of pona 3000 optical amplifiers is designed to meet the most demanding noise performance requirements of catv and fttx applicati ons, and performs all the functions required of an optical amplifier for sy stem integration. pona 3000 series optical amplifiers provide optical isol ation on the input and output of the gain block for stable, low noise operation. the input and output optical signal power levels are detected for monitoring and control. the input optical signal is amplified with active gain control for a constant output power level, or with active output power control for const ant gain mode. the pona 3000 series optical amplifiers also provide monitori ng functions and associated alarms for all vital characteristics. the optical output of the pona 3000 series optical amplifiers can be split into number of ports by an optional internal splitter. pona3000 series includes ac/dc power supply, front panel, optical splitters, network card and all necessary connectors. general and mechanical specifications general property requirement comments operating wavelength 1545 ~ 1565nm standard operating case temperature 0 ? c to 50 ? c standard storage temperature -40 ? c to 85 ? c standard operating humidity 20% to 85% non-condensing voltage supply range 85 vac to 265 vac 50/60 hz -36 to ?60 v dc ac version dc version *(redundant power supply is available by customer request optical connectors see ordering information user specified dimensions in inches 19.0?w x 14.76 ?d x 3.44?h 19?? rack mounted, 2 ru pona 3000 series
datasheet | january 2012 fiber optics | rev 2012.01 information contained herein is deemed reliable and accurate as of the issue date. emcore reserves the right to change the desi gn or specification at any time without notice. performance specifications 1 property unit limit pona models comment 3027 3030 3032 3033 3035 3037 operating input power pin (dbm) max +12 +12 +12 +12 +12 +12 operating input power pin (dbm) min -10 -10 -10 -10 -10 -10 output power po (dbm) 27.0 30.0 32.0 33.0 35.0 37.0 nominal (note 2) noise figure nf (db) typ/max 5.5/6.0 5.5/6.0 5.5/6.0 5.5/6.0 5.5/6.0 5.5/6.0 (note 3) static gain flatness gf (db) max +/-2.0 +/-2.0 +/-2.0 +/-2.0 +/-2.0 +/-2.0 (note 4) dynamic gain flatness (db) max +/-2.50 +/-2.50 +/-2.50 +/-2.50 +/-3.00 +/-3.00 (note 5) output power stability (db) max +/- 0.2 +/- 0.2 +/- 0.2 +/- 0.2 +/- 0.2 +/- 0.2 (note 6) power consumption (steady state regime) psys (w) max 20 15 35 20 45 25 55 30 65 40 70 45 50 o c case (premium) 50 o c case (economy) (note7) remnant pump power to output prp (dbm) nom. <-30 <-30 <-30 <-30 <-30 <-30 notes: 1. unless stated otherwise all sp ecifications apply over the full temperature range and humidity 2. depending on the fiber optic patch cord interface the measur ed value can vary up to 0.5 db less than the actual value. 3. measured @ 25 ? c, ? pin = 0 dbm. can be measured only after splitting output power 4. measured with a swept probe signal (pp), where pp = 0 dbm @ 25 ? c 5. measured with a swept probe signal (pp), and a fixed tone signal (pt) @ 1553nm; (pt = pp+20 db; pt + pp = 0 dbm) @ 25 ? c; 6. stability over polarization and temperature 7. premium version ? pona with cooled, telecordia qualified pumps economy version ? pona with uncooled pumps table for determination of minimal output optical power per port (dbm) minimum optical power per port (dbm) pona models number of ports 3027 3030 3032 3033 3035 3037 1 27 30 32 33 35 37 2 23.5 26.5 28.5 29.5 31.5 33.5 4 20.2 23.2 25.2 26.2 28.2 30.2 8 16.8 19.8 21.8 22.8 24.8 26.8 16 13.4 16.4 18.4 19.4 21.4 23.4 32 10.0 13.0 15.0 16.0 18.0 20.0 64 7.0 10.0 12.0 13.0 15.0 17.0 pona 3000 series
datasheet | january 2012 fiber optics | rev 2012.01 information contained herein is deemed reliable and accurate as of the issue date. emcore reserves the right to change the desi gn or specification at any time without notice. block diagram: cladding pump technology cladding pump technology uses erbium/ytterbium fiber optic assemblies (double clad fiber and multi-mode pump lasers) to produce cost effective high power optic al amplification. this technology enables the development of higher power edfas- something that was cost inhibitor when usin g standard erbium fiber and single mode pumps. sample fttx architecture pona 3000 series 980 nm pump output monitor input monitor multi-mode pumps drive electronics er er/yb assembly input hybrid filter / isolator isolator 1% tap 980 nm pump output monitor input monitor multi-mode pumps drive electronics er er/yb assembly input hybrid filter / isolator isolator 1% tap ont edfa 20 outputs of 20 dbm wdm rf olt homes businesses multi dwelling units splitter ont video 1490nm 1310nm 1550nm 20 km 1550nm tx -voice -data -video data voice splitter splitter splitter ont ont ont ont ont ont ont ont ont ont ont ont edfa 20 outputs of 20 dbm wdm rf olt homes businesses multi dwelling units splitter ont ont video video 1490nm 1310nm 1550nm 20 km 1550nm tx -voice -data -video data data voice voice splitter splitter splitter ont ont ont ont ont ont ont ont ont ont ont ont ont ont ont ont ont ont ont ont
datasheet | january 2012 fiber optics | rev 2012.01 information contained herein is deemed reliable and accurate as of the issue date. emcore reserves the right to change the desi gn or specification at any time without notice. outline drawing ac versions shown below with 8 optical output ports dc versions shown below with 8 optical output ports pona 3000 series
datasheet | january 2012 fiber optics | rev 2012.01 information contained herein is deemed reliable and accurate as of the issue date. emcore reserves the right to change the desi gn or specification at any time without notice. ordering information pona30 - - - - * class: premium: utilizes cooled pump lasers economy: utilizes un cooled pump lasers * pona 3000 series with power higher then 30 dbm per port mu st have special output optical connector(s) and optical bulkhead(s). their type(s) must be verified prior to placing purchase order. compliance information fcc: subpart b. part 15, class ?a? unintentional radiators ce:en50083-2 19995 with amendment 1, which inco rporates en 55013 radiated and conducted emissions en 61000-4-3 radiated immunity en 55020 conducted immunity en 61000-3-2 harmonics all components meet telecordia gr-1312 and gr -486 standards (except pumps in economy class) fit rate: 90% level of confidence < 2500 @ 30 o c premium pona 3035 90% level of confidence < 2000 @ 30 o c economy pona 3035 power level connector options # of output ports class input voltage 27: 27 dbm sc: sc/apc 01: 1 port p: premium ac: 90-260 vac 50/60 hz 30: 30 dbm fc: fc/apc 02: 2 ports e: economy dc: -48 vdc 32: 32 dbm ec: e2000/apc 04: 4 ports 33: 33 dbm tc: sc/upc 08: 8 ports 35: 35 dbm gc: fc/upc 16: 16 ports 37: 37 dbm scdplx: sc/apc duplex 20: 20 ports 32: 32 ports 64 : 64 ports pona 3000 series
datasheet | january 2012 fiber optics | rev 2012.01 information contained herein is deemed reliable and accurate as of the issue date. emcore reserves the right to change the desi gn or specification at any time without notice. laser safety information this product meets the applicable requirements of 21 cfr 1010 & 1040 and is classified as a class iv laser product based on the maximum optical output power shown below. during use as intended, the laser energy is fully contained within the fiber network such that there is no accessible laser radiati on and would meet the requirements for a class i laser product. the laser product report has been submitted to the cdrh and the accession number is expected by october 2006. wavelength = 1545 ~ 1562 nm (dependant on input source) maximum output power = 5 w (single output, 37 dbm model) . pona 3000 series
|
